|
|
Monitoring Stations
& Test Stations
for Cathodic Protection
by Handley Industries
 2-Inch Monitoring
Stations
-
Terminals on the outside of the lid provide fast, convenient test checks.
- Available with pre-wiring to outside terminals in the lid. One red and one black
15" coil of plastic coated, #12 AWG type TW, 600 volt, oil resistant wire is
contained in the station.
- Wires easily uncoil to reach connection points.
- No wires with terminals only is available.
- The 15" ABS plastic box has a 2-3/8" I.D. and is available in either straight
or flanged top for installation at grade level.
- Adjustable-to-grade test stations are available upon request.
- Boxes are flared and squared to prevent pull-out, turning or settling.
- Cast iron lids are marked "Test". Plastic lids are marked "Test
Station" and include a metal reflector for locating.
- Custom lids may be ordered for an additional charge.
- A permanent "Real" magnet is in every box for easy location with electronic
locator.
- Monitor lids available in marker posts. See marker post specs to order.
- Underground installation protects the station from vandalism and is esthetically
superior; however, above ground monitor stations are also available.
How to Order 2" Monitoring
Stations
Build a model number like M2FWA. Start with
M2 for a
2" monitoring station. Then fill in the remaining positions from the choices below.
Please consult Farwest for any special requirements.
| Position 0. |
M2 = 2" monitoring
station |
| Position 1.
Upper tube type. |
F = Flanged top, plastic
S = Straight top |
| Position 2.
Wiring code. |
N = Not wired
W = Wired |
| Position 3.
Lid color. Black is standard. |
A = Yellow |
How to Order 2" Monitoring
Station Parts & Accessories
For replacement lids, build a model number like
LIM2NA. Start with LIM2
for a 2" lid, then fill in the remaining positions from the choices below. The
pentagon wrench is PW.
| Position 0. |
LIM2 = Lid for 2"
monitoring station |
| Position 2.
Wiring option. |
N = Not wired
W = Wired |
| Position 3.
Lid color. Black is standard. |
A = Yellow |
|
2-Inch Cathodic Test
Stations
-
 The 15"ABS plastic box has a 2-3/8" I.D. and is available in either straight
or flanged top for installation at grade level.
- "Adjustable to grade" test stations are available upon request.
- Terminal blocks are secured in place beneath the lid. Wires are automatically pulled up
when the lid is removed.
- 0, 1, 2 or 5 terminals are available. All terminals are made of solid brass.
- Boxes are flared and squared to prevent pull-out, turning or settling.
- Cast iron lids are marked "Test". Plastic lids are marked "Test
Station" and include a metal reflector for locating.
- One piece locking lids are standard. No parts to lose.
- Custom lids are available for an additional charge.
- A permanent "Real" magnet is in every box for easy location with electronic
locator.
- Terminal Jumpers are available upon request.
- Test terminals can be incorporated with Handley valve boxes.
- Underground installation protects the station from vandalism and is esthetically
superior; however, above ground test stations are also available.
- Test lids are available for marker posts. See marker post specs to order.
How to Order 2" Cathodic Test
Stations
Build a model number like T2PF5AKNQ. Start with
T2
for a 2" cathodic test station. Then fill in the remaining positions from the choices
below. Please consult Farwest for any special requirements.
| Position 0. |
T2 = 2"
cathodic test station |
| Position 1.
Lid material. |
I = Iron
P = Plastic |
| Position 2.
Upper tube type. |
F = Flanged
top, plastic.
S = Straight top. |
| Position 3.
Number of terminals |
0 = 0
terminals with a board
1 = 1 terminal on a board
2 = 2 terminals on a board
3 = 1 terminal in the wedge nut
5 = 5 terminals on a board
6 = 0 terminals, NO terminal board |
Position 4. Lid color.
Black is standard. |
A = Yellow
B = Blue
C = Green
D = Red
E = White
F = Orange |
| Position 5. Jumper option. |
J = One jumper
K = Two jumpers |
Positon 6. Magnet. One
magnet
located in the tube is standard. |
M = No magnet at all
N = One magnet in the wedge nut
(none on the tube)
P = Two magnets in the wedge nut
(none on the tube) |
Position 7. Tube design. A
15" straight
tube flared at the bottom is standard. |
Q = Telescoping, 18
5/8"-24", flared
R = Telescoping, 18 5/8"-24", arched |
How to Order 2" Test Station
Parts & Accessories
For replacement lids, build a model number like
LIT2P2A1N. Start with LIT2
for a 2" lid, then fill in the remaining positions from the choices below. The
pentagon wrench is PW.
| Position 0. |
LIT2 = Lid for
2" cathodic test station |
| Position 1.
Lid material. |
I = Iron
P = Plastic |
| Position 2.
Number of terminals |
0 = 0
terminals with a board
1 = 1 terminal on a board
2 = 2 terminals on a board
3 = 1 terminal in the wedge nut
5 = 5 terminals on a board
6 = 0 terminals, NO terminal board |
Position 3. Lid color.
Black is standard. |
A = Yellow
B = Blue
C = Green
D = Red
E = White
F = Orange |
| Position 4. Jumper option. |
1 = One jumper
2 = Two jumpers |
Positon 5. Magnet. One
magnet
located in the tube is standard. |
M = No magnet at all
N = One magnet in the wedge nut
(none on the tube)
P = Two magnets in the wedge nut
(none on the tube) |
|
 4-Inch Cathodic Test
Stations
- The 18" ABS plastic box has a 4" I.D. and also is standard with a 1-1/2"
cast iron flange for heavy duty installation at grade level.
- "Adjustable to grade" test stations are available upon request.
- Terminal blocks are secured in place beneath the lid.
- Wires are automatically pulled up when the lid is removed.
- 0, 1, 2, or 5 terminals are available.
- 10 connections on 5 post-type terminals is also available.
- All terminals are made of solid brass.
- Boxes are flared and squared to prevent pull-out, turning or settling.
- Cast iron drop-in or one-piece locking lids marked "Test Station" are
available.
- Custom lids are available for an additional charge.
- Terminal jumpers are available.
- Test terminals can be incorporated with Handley valve boxes.
- Underground installation protects the station from vandalism and is esthetically
superior; however, above ground test stations are also available.
How to Order 4" Cathodic Test
Stations
Build a model number like T43N2. Start with
T4 for a
4" cathodic test station. Then fill in the remaining positions from the choices
below. Tube length is 18". Lid color is silver. Please consult Farwest for any
special requirements.
| Position 0. |
T4 = 4"
cathodic test station |
| Position 1.
Number of terminals |
3 = 5 post
type terminals on a board
5 = 5 screw type terminals on a board
6 = 0 terminals, NO terminal board |
Position 2. Lid type
option.
Locking lids are standard. |
N = Non-locking |
| Position 3. Jumper option. |
1 = One jumper
2 = Two jumpers |
How to Order 4" Test Station
Parts & Accessories
For replacement lids, build a model number like
LIT43N1. Start with LIT4
for a 4" lid, then fill in the remaining positions from the choices below. The
pentagon wrench is PW.
| Position 0. |
LIT4 = Lid for
4" cathodic test station |
| Position 1.
Number of terminals |
3 = 5 post
type terminals on a board
5 = 5 screw type terminals on a board
6 = 0 terminals, NO terminal board |
Position 2. Lid type
option.
Locking lids are standard. |
N = Non-locking |
| Position 3. Jumper option. |
1 = One jumper
2 = Two jumpers |
|
|
