6 Branch
Locations

Tulsa, OK

Home Products Contact Us Search Request Quote Order Online
 

    
Tapecoat®
Moldable Sealant


Watertight, conformable coating for corrosion protection
of irregular surfaces

Basic Use

Tapecoat Moldable Sealant is a conformable water tight coating for irregular surfaces, such as bolt style mechanical couplings, bell and spigot joints, saddle tees or leak clamps; as a sealant in vaults, on underground tracer wire and other low voltage manual wire connections, on anode wire connections, as an insulating adhesive with shrinkable tubing.

Composition

Tapecoat Moldable Sealant is a 100% solids formulation of thermoplastic elastomeric and synthetic resins. Blended in this adhesive is an “integrated primer.”

Technical Data

Color Gray
Service temperature -30ºF to 120ºF (-35ºC to 40ºC)
Application temperature Above -10ºF (-23ºC)
Total thickness 40 and 60 mils (1.0 and 1.5 mm)
Adhesion 165 oz/inch width
Flexibility 1/2" radius at -20ºF without cracking
Dielectric strength > 12 kV
Cathodic disbonding Pass (ASTM G-8)
Insulation resistance 108 megohms
Water absorption < 0.05%

Application

Surface Preparation

Surface must be clean and dry. Moisture, dust, dirt, rust or other foreign matter should be removed by scraping or wire brushing. Remove oil and grease, etc, with suitable detergent. Optional cleaning method SSPC 6 Commercial Blast.

Application

  • Priming: Because TC-Moldable Sealant comes with an "integrated primer" built into the adhesive, liquid primer may not be required. TC Omniprime Primer has boon developed specifically for use with Moldable Sealant. The coverage is approximately 300 square feet per gallon. Let TC Omniprime dry to a tacky consistency before applying Moldable Sealant.
      
  • Sealant Application: Remove the release liner on one side of the moldable sealant and apply to the surface to be protected. Remove the remaining liner and use it as an aid in molding the sealant until all voids and crevasses have been filled. Liner may then be used as an overwrap for additional mechanical protection.

Technical Service

Contact Corrosion Control Products Company.
 

Corrosion Control Products Company

 Epoxy Coatings
 Heat-Shrink Coatings
 Mastic Coatings
 Petrolatum Coatings
 Tape Coatings
 Surface Decontamination
 Moisture Seal Products
 Rockshields
 Inspection Instruments
 Insulated Fittings
 Insulators & Seals
 Flange Insulation
 Pipeline Cleaning Pigs
 Composite Systems
 Accessory Products

  

Farwest Corrosion Control Company

 Impressed Anodes
 Sacrificial Anodes
 Cable & Splicing
 DC Supplies & Rectifiers
 Remote Monitoring
 Polarization Cells
 Overvoltage Protection
 Junction & Bond Boxes
 Test Stations & Markers
 Reference Electrodes
 Test Instruments
 Insulating Materials
 Pipe Coatings & Tape
 Marine Products Division
 Offshore CP Systems
 Miscellaneous Products

  

More Corrosion Control Products Resources

 Search this Website
 Request Quote
 Order Products Online
 3-Ring Binder Catalog
 Industry Links
 CCP Suppliers

 MSDS
  

Home

Products Search Request Quote Order Online

Corrosion Control Products Company
800-421-2623

Tel: 

 310-532-9314
Fax:  310-532-1472

1480 West Artesia Blvd., Gardena, CA 90248-3215, USA
 www.ccpco.com

© 1996-2006 Corrosion Control Products Company | Privacy Statement